Discontinued ProductNote: The contents of this page is as of the time it was created.

HF/50MHz TRANSCEIVER

IC-7200

Simple & Tough with IF DSP

IF DSP

The latest IF DSP technology is employed in the IC-7200. While the IC-7200 is an entry-class transceiver, advanced digital features are comparable to higher class transceivers.

AGC Loop Management

Distortion and blocking from strong nearby signals are prevented by placing DSP functions inside the AGC loop. The AGC time constants are selectable from fast, slow and off for each operating mode.

Digital IF Filter

Optional filters will be never required for the IC-7200. The built-in digital filter allows you to flexibly select the filter width and shape from soft and sharp* and provides cuttingedge filter characteristics.

 

* Filter shape is selectable for SSB and CW modes only.

Digital Twin PBT

Only Icom brings you Twin Passband tuning! Tailor your IF passband with the Twin PBT by electronically shifting the upper and lower edges of the IF filter. Depending on the use of the concentric knobs, you can either narrow the IF passband, or shift the entire passband to eliminate interfering signals.

Manual Notch Filter

The manual notch filter delivers more than 70dB of attenuation. Strong interfering tones will be eliminated without adversely affecting the AGC loop performance. On the bottom right of the front panel, a dedicated control knob adjusts the notch filter frequency.

Digital Noise Reduction

Digital noise reduction reduces background noise and improves the signal-to-noise ratio. The noise reduction level is adjustable in 16 steps. It improves the readability of voice and data signals.

Digital Noise Blanker

The noise blanker reduces pulse-type noise such as engine ignition and sparking. The NB level and width (blanking duration) are adjustable in 100 steps.

High Stability Transmitter

The DDS (Direct digital synthesizer) creates a clear, clean transmit signal and improves the C/N ratio. With a dual-fan cooling system, the IC-7200 provides stable high quality output even during high duty cycle operation.

USB Port for PC Control

The IC-7200 can be controlled by a PC through a USB port using the CI-V data format. In addition, modulator and received audio can also be transferred over the USB cable. By using appropriate external software, you can record incoming call and/or transmit preprogrammed messages from your PC.

RF Speech Compressor

The digital RF speech compressor increases your average talk power in SSB mode. Even when the compression level is increased, the DSP controlled RF speech compressor provides low distortion audio.

CW Mode Operation

Full break-in, selectable CW carrier point (USB or LSB) and adjustable CW pitch are also standard.

Tough Construction Against Water Intrusion

Waterproof protection technologies that are used in Icom’ s marine radios are applied to the buttons and knobs on the front panel to provide a measure of protection against water intrusion.

 

*IC-7200 is NOT waterproof.

Rugged Design for Outdoor Use

The rugged design of the IC-7200 means your enjoyment of this rig is not limited to your shack only.

Other Features

   ・ RIT
   ・ VOX
   ・ ±0.5ppm frequency stability
   ・ LCD backlight (Hi/Lo/Off)
   ・ CI-V interface
   ・ 201 memory channels
   ・ Built-in 20dB attenuator
   ・ Preamplifier
   ・ Dial lock
   ・ Auto TS function
   ・ 1Hz step tuning
   ・ Band stacking register
   ・ Built-in voice synthesizer
   ・ Quick split
   ・ Front facing speaker
   ・ Quick set mode

“Rear Bumper”

The “rear bumper” protects various connectors on the rear panel and lets you stand the radio on its rear end when the antenna is disconnected, such as while moving or packing the radio.

General

Frequency coverage*1
(Differs according to version)
Rx :
0.030–60.000000MHz*2

Tx :
1.800– 1.999999MHz 3.500– 3.999999MHz
5.255– 5.405MHz*3 7.000– 7.300MHz
10.100–10.150MHz 14.000–14.350MHz
18.068–18.168MHz 21.000–21.450MHz
24.890–24.990MHz 28.000–29.700MHz
50.000–54.000MHz
Mode USB, LSB, CW, RTTY (FSK), AM
Frequency stability Less than ±0.5ppm
Maximum current drain 22.0A
Power supply requirement 13.8V DC ±15 % (negative ground)
Antenna connector SO-239 (50Ω)
Number of memory
channels
201ch (199 regular, 2 scan edges)
Dimensions
(W×H×D; Projections
are not included)
241×84×281 mm
9.49×3.31×11.06 in
Weight (approx.) 5.5 kg; 12.1 lb

*1 Shows USA version. Frequency coverage depends on version.
*2 Guaranteed range: 0.5-29.999 and 50-54.000 MHz.
*3 Some frequency ranges are not guaranteed.

Transmitter

Output power

SSB, CW, RTTY:
2–100 W

AM:
1–25 W

Spurious emissions Less than –50dB (HF)
Less than –63dB (50MHz)
Carrier suppression More than 50dB
Unwanted sideband More than 50dB
Microphone connector 8-pin connector (600Ω)

Receiver

Sensitivity
(10dB S/N, Preamp ON, Filter shape sharp)
SSB, CW:
Less than 0.16μV (1.8–29.995MHz):
Less than 0.13μV (50MHz band)

AM:
Less than 13μV (0.5–1.8MHz)
Less than 2μV (1.8–29.995MHz)
Less than 1μV (50MHz band)
Selectivity SSB(BW: 2.4kHz, sharp):
More than 2.4kHz/–6dB
Less than 3.6kHz/–60dB

CW(BW: 500Hz, sharp) :
More than 500Hz/–6dB
Less than 900Hz/–60dB

RTTY (BW: 350Hz):
More than 360Hz/–6dB
Less than 650Hz/–60dB

AM (BW: 6kHz):
More than 6.0kHz/–6dB
Less than 15.0kHz/–60dB
Spurious and image
rejection
More than 70dB
(Except 12 IF through on 50MHz band)
AF power
(at 10% distortion with an 8Ω load)
More than 2.0W
External speaker
connector
2-conductor 3.5 (d) mm (18″) /8Ω


All stated specifications are subject to change without notice or obligation.

Catalogs / Brochures

Brochures Name Size
IC-7200 811KB

Instruction Manual / Guides

Name Model Name Note
Instruction manual IC-7200
Advanced Instructions IC-7200

Firmware / Software

Type Model Name Version Last Update
USB Driver IC-7100/IC-7200/IC-7300/IC-7410/IC-7600/IC-7610/IC-7850/IC-7851/IC-9100/IC-9700/IC-R8600 Version 1.30 Jun.07.2018
USB Driver IC-7100/IC-7200/IC-7300/IC-7410/IC-7600/IC-7610/IC-7850/IC-7851/IC-9100/IC-9700/IC-R8600 Version 1.20 Oct.05.2017
USB Driver IC-7100/IC-7200/IC-7410/IC-7600/IC-9100 Ver.1.10 Jun.07.2018
USB Driver IC-7200/IC-7600 Ver.1.00 Feb.26.2009
Control software RS-BA1 Version 2 Version 2.60 May.16.2024