Amateur VHF Equipment

VHF Simplex Operation and Spectrum Scope Use

By Jim Wilson, K5ND Updated on May 4, 2020
IC-9700 spectrum scope display

Introduction

With VHF simplex operation it's all about finding the other stations for general communication, DXing, or contest QSOs, and there's no better tool than a spectrum scope for finding those stations. Two great rigs with a built-in spectrum scope covering VHF are the IC-7300 for 6 meters and the IC-9700 for 2 meters, 70 centimeters, and 23 centimeters.

Spectrum Scope

I put those rigs to use in the ARRL January 2020 VHF Contest. You can find the details of my rover setup and operation at VHF Rover Contesting – Truly Moving QSOs. The spectrum scopes and similar operating controls across both rigs were huge during my rover run.

Key Benefit

During busy contests, catching a glimpse of a signal on the scope makes all the difference in finding stations and getting them into the log.

IC-9700 Spectrum Scope showing FM signal from the International Space Station

IC-9700 Spectrum Scope showing FM signal from the International Space Station

I've now used the Icom IC-9700 VHF/UHF All Mode Transceiver in VHF contests as a rover as well as from my home station for local activity nights and in a couple of tropospheric openings. Not only is it a super transceiver but the spectrum scope adds an entirely new dimension to your operating.

Finding Other Stations

As mentioned above, spotting other stations that are away from your receive frequency is a spectacular use of the IC-9700's spectrum scope. For example, the 2-meter SSB calling frequency is 144.200 MHz, so it's good to monitor that frequency throughout a VHF contest.

IC-9700 Spectrum Scope showing SSB signal at 144.260 while monitoring audio on 144.250

Monitoring SSB signals while watching adjacent frequencies

VHF Calling Frequencies

Band Calling Frequency Common Modes
2 meters 144.200 MHz SSB, CW
70 cm 432.100 MHz SSB, CW
6 meters 50.125 MHz SSB, CW

Another helpful feature is the Scope SPAN setting. Here you can set it narrow, +/-2.5 kHz, or expand the amount of band that you're monitoring up to +/-500 kHz. What I like about that is while I'm perhaps set up for WSJT-X FT8 at 144.174 MHz, with a wide setting on the spectrum scope I can see what's happening at 144.200 MHz on SSB – or vice versa.

💡 Pro Tip: In areas with low activity (like North Texas), any movement on an essentially blank screen is worth investigating!

Verifying Correct Operation

One of the features of the spectrum scope that I really appreciate is viewing your transmitted signal. For this to work you'll need to make sure that under SCOPE SET, you've turned "Scope during TX" to ON.

IC-9700 Spectrum Scope showing FT8 signal during transmit.

Monitoring your own transmission quality

With this view you can readily see your transmitted spectrum. It's particularly useful to make sure your WSJT-X FT8 signal audio level is set correctly. Too much and you'll get splatter on your audio signal. This causes interference to other stations and may also make your own signal unreadable.

IC-9700 Spectrum Scope showing an FT8 signal with too high audio level during transmit

IC-9700 Spectrum Scope showing an FT8 signal with too high audio level during transmit. This is a very good way to determining correct operation using WSJT-X.

Spectrum Scope Setup

There are quite a few settings that you can adjust on the spectrum scope. I suggest spending some time tweaking with the colors, the line, etc. to find exactly the right combination that fits your eye and helps you readily find other signals.

Setup Recommendations

  • Experiment with both center and fixed modes
  • Adjust waterfall settings for your operating style
  • Try different waveform types (fill + line works well)
  • Customize colors for maximum visibility

In the past I've primarily used the center mode on the spectrum scope but a buddy pointed out the benefits of using the fixed mode. With this mode you can set the upper and lower frequencies and then move your operating frequency between them.

IC-9700 Spectrum Scope with fixed frequency range

Fixed mode allows monitoring a specific frequency range

The waterfall can be particularly helpful as it provides insight into signals over time. If you miss the station on the scope, you can see it receding off the screen in the waterfall. This too has a number of setting from speed, size, to color.

Conclusion

It used to be that you could purchase a separate spectrum scope and add it to your station. Now the spectrum scope is an essential tool in your operating arsenal. The IC-9700 as well as the IC-7300 recognize that and provide one of the best scopes built in. Try it out.

📡 Final Thought: The spectrum scope transforms VHF operating from guesswork to precision, especially during contests and DX opportunities.

Jim Wilson, K5ND

About Jim Wilson, K5ND

Jim Wilson is an experienced VHF contester and rover operator from North Texas. He specializes in weak-signal VHF/UHF operation and regularly participates in major contests with his mobile rover station.

Amateur Radio VHF Equipment Contesting Icom

Found this VHF guide helpful?

Share these spectrum scope techniques with fellow ham operators!