English | Español | Português
Icom America - 2 way radios

F1100D / F2100D

IDAS™ VHF/UHF Portables

Specifications

Specifications

General
Frequency coverage (MHz)
F1100D/DS/DT
136–174MHz

  F2100D/DS/DT
400–470MHz
450–512 MHz
Number of channels
F1100DT/DS
128 channels
8 zones
F1100D 
16 channels
F2100DT/DS 
128 channels
8 zones
 F2100D 
16 channels
Type of Emission
  Analog:
  Digital (IDAS):

11K0F3E
4K0F1D, 4F0F1E
Power supply requirement 7.5V DC nominal
Current drain
  TX High
  RX Max. auidio/ Sandby
F1100D/DS/DT
1.3 A
520 mA /110 mA
(Max. audio (internal SP)/Standby)
F2100D/DS/DT
1.4 A4
520 mA /110 mA
(Max. audio (internal SP)/Standby)
Antenna impedance 50Ω
Operating temperature range –30°C to +60°C; –22°F to +140°F (Radio specification)
Dimensions (W×H×D)
(Projections not included)
F1100DS/D, F2100DS/D:
52.2 × 111.8 × 29.4 mm; 2.1 × 4.4 × 1.2 in (With BP-280)

F1100DT, F2100DT:
52.2 × 111.8 × 34.1 mm; 2.1 × 4.4 × 1.3 in (With BP-280)
Weight (With BP-280 & MB-133) F1100D, F2100D: 260 g; 9.2 oz
F1100DS, F2100DS: 270 g; 9.5 oz
F1100DT, F2100DT: 280 g; 9.9 oz
Transmitter
Output power (Hi, L2, L1)
F1100D/DS/DT
5W, 2W, 1W
  F2100D/DS/DT
4W, 2W, 1W
Max. frequency deviation ± 5.0 kHz (25 kHz), ±4.0 kHz (20 kHz), ±2.5 kHz (12.5 kHz)
Spurious emissions 70dB minimum
Frequency stability ±1.0ppm
Audio harmonic distortion 0.7% typ. (25 kHz), 0.9% typical (20 kHz)
1.0% typical (12.5 kHz) (at AF 1 kHz 40% deviation)
FM Hum and Noise
(without CCITT filter)
F1100D/DS/DT
40 dB typical (12.5 kHz)
  F2100D/DS/DT
44 dB typical (12.5 kHz)
Residual modulations
(with CCITT filter)
F1100D/DS/DT
52 dB typical (25 kHz)
50 dB typical (20 kHz)
  F2100D/DS/DT
54 dB typical (25 kHz)
52 dB typical (20 kHz),
FSK error 5.0% max.
Ext. microphone connector 3-conductor 2.5 (d) mm (1⁄10")⁄2.2kΩ
Receiver
Sensitivity
  (at 12dB SINAD)

  (at 20 dB SINAD)


  (at 5% BER)

F1100D/DS/DT
0.21 μV typical

–4 dBμV typical emf


–8 dBμV typical emf
(0.20 μV typical)
F2100D/DS/DT
0.24 μV typical

–5 dBμV typ. emf (25/20 kHz)
–2 dBμV typ. emf (12.5 kHz)

–8 dBμV typical emf
(0.20 μV typical)
Adjacent channel selectivity
F1100D/DS/DT
77 dB typ. (25 kHz)
74 dB typ. (12.5 kHz)
69 dB typ. (12.5 kHz)
59 dB typ. (digital)
  F2100D/DS/DT
76 dB typ. (25 kHz)
75 dB typ. (12.5 kHz)
69 dB typ. (12.5 kHz)
58 dB typ. (digital)
Spurious response 80dB typical
Intermodulation rejection
F1100D/DS/DT
75 dB typ. (25/12.5 kHz)
71 dB typ. (digital)
  F2100D/DS/DT
77 dB typ. (25/12.5 kHz)
70 dB typ. (digital)
Hum and noise
   (With CCITT filter)


   (Without CCITT filter)
F1100D/DS/DT
47 dB typ. (25 kHz)
43 dB typ. (12.5 kHz)

52 dB typ. (25 kHz)
50 dB typ. (20 kHz)
  F2100D/DS/DT
42 dB typical (12.5 kHz)


50 dB typ. (25 kHz)
48 dB typ. (20 kHz)
AF output power (at 5% distortion)
   Internal SP
   External SP

1500 mW typical (With an 8 Ω load)
800 mW typical (With an 8 Ω load)
Ext. speaker connector 2-conductor 3.5 (d) mm (1⁄8″)/8Ω

All stated specifications are subject to change without notice or obligation. Measurements made in accordance with TIA-603 (USA/EXP) or EN 300-086, EN 301-166 (EUR). The IC-F1100DT/DS/D VHF versions are under evaluation as of May 2018.

Applicable U.S. Military Specifications & IP Rating

Icom makes rugged products that meet MIL-STD requirements and strict environmental standards as follows.

Standard MIL 810 G
Method Proc
Low Pressure 500.5 I, II
High Temp. 501.5 I, II
Low Temp. 502.5 I, II
Temp. Shock 503.5 I-C
Solar Radiation 505.5 I
Rain Blowing/Drip 506.5 I, III
Humidity 507.5 II
Salt Fog 509.5
Dust Blowing 510.5 I
Immersion 512.5 I
Vibration 514.6 I
Shock 516.6 I, IV

Also meets equivalent MIL-STD-810-C, -D, -E and -F.

Ingress Protection Standard
Dust & Water IP67/55/54

Supplied Accessories

  • Battery pack, BP-280
  • Belt clip, MB-133
  • Antenna
  • Desktop charger, BC-213*
  • AC adapter, BC242*

*Included with some versions only.

 

View our blog